Compatible Spare Parts for the Bristan Artisan

Please select from the available product options shown below

Product CodeProduct OptionsDescriptionUnit PriceBuyDespatch Time
ArtisanQA-ABAnticlockwise (to open) blue1/2" x 20 x 53mm£6.99 Today
ArtisanQA-CRClockwise (to open) red1/2" x 20 x 53mm£6.99 Today
ArtisanQA-PPair (1 x red, 1 x blue)1/2" x 20 x 53mm£13.98 Today
Product CodeProduct OptionsDescriptionUnit PriceBuyDespatch Time
SB27-SSingle27mm adaptor bush£7.94 Today
SK19-SSingleO Ring Tap Repair Kit£6.00 Today
SL05-SSinglePremium Disc/O'Ring Lubricant£2.99 Today
SL50-SSingleRegin Grease 50ml£9.99 Today
ST17-SSingle17mm spanner£6.50 Today

SPARES FOR BRISTAN ARTISAN KITCHEN MIXER MONO TAP 20 SPLINE VERSION compatible with 2998827300
The 20 spline cartridge fits the easyfit version only. If you do not know which version you have then you will need to check the number of splines.
**Please be aware for the Artisan Filter tap we can only supply the HOT side and cannot supply the cold/filter diverter cartridge

Watch video below for step by step tutorial how to replace the tap cartridges

When you remove your old Cartridge / Insert from the tap the bush usually remains inside the tap block however sometimes it comes out together with the valve. If the valve is stuck inside the bush you can try to separate them. If you are unable to separate the valve from the bush then you will need to purchase the valve together with the bush.

If your Artisan tap is leaking from the base of the spout where the spout meets the tap body (the neck) then you will need to replace the O Rings / washers inside the spout. The O'ring kit is known by original part number 1425R SP1425.

If you require a new antisplasher this is our part SR63C/CB (available in Chrome or brushed) Original codes known by 133.0068.762 SP1263 /1263R / 02635 your original part may have Neoperl stamped around the edge.

Bristan Artisan Frequently asked questions

How to I remove the Artisan tap handle?
Use 2mm allen key to undo handle. The grub screw is located on the underside of the handle. You can pull the lever forwards to access the screw at the back if you need more space.

How do I know if need the adaptor bush?
Until you remove the cartridge from the tap you will not know if you need this part. This is because sometimes the bush gets corroded to the tap and remains in the tap body, and other times it comes out corroded to the tap cartridge.

Can I remove the adaptor bush from the old cartridge?
Yes you can but it can be very hard to remove due to corrosion. You can try using very hot water, followed by cold water over it, to help break the corrosion seal. The bush unscrews from the cartridge anticlockwise. You will likely ed to use some grips or put it in a vice to remove it. If you cannot separate it you will need to replace the bush.

How do I remove the spout and replace the o'rings inside the spout?
Use 2.5mm allen key to undo grub screw at the back holding the spout in place. pull spout up and out of the tap body. You can watch our How to video above.

What size spanner do I need to remove the Bristan Artisan tap handle?
You will need a 17mm or an adjustable spanner

Tap Magician are the UK experts in ceramic disc tap cartridges and leaky taps. We offer high quality fully compatible tap valve spares for most UK kitchen, basin, bath and shower mixers. Easily repair and doctor your leaking or dripping hot and cold taps. Traditional or ceramic valve type. We have experienced advisors available for any technical support you need help or advice with. We stock the spare parts for all of our valves for easy and cheap low cost future maintenance (ceramic disc internals and silicone seals and washers and o'rings). We offer a 12 month warranty on all of our products.